This board covers growing in a closed room where you set every condition yourself. The weather no longer decides anything for you. That also means any setting can be wrong.
The settings you control are:
- the type of lamp and how strong it is
- the temperature and humidity you hold the room at
- the carbon dioxide (CO₂) level in the air
- the irrigation system that feeds the pots
Three decisions that shape everything else
Most other settings in an indoor room follow from three choices. Get these three right first. Fine-tune the rest afterwards.
1. The light: which lamp, and how much light reaches the plants each day
The first choice is the lamp type. The common options are LED (light-emitting diode) panels, HPS (high-pressure sodium) lamps and CMH (ceramic metal halide) lamps.
The second choice is how much light reaches the canopy. The canopy is the top layer of leaves and buds that the light falls on. The total light the canopy receives over a whole day is called the daily light integral (DLI). The lamp’s wattage does not tell you this number. Hanging height and how the light spreads change how much of it actually arrives at the leaves.
Translator’s note: In a Thai room at 30–35 °C, every lamp is also a heater. Your air conditioner has to remove the lamp heat on top of the heat coming through the walls and roof. Before you buy lamps, check that the air conditioning can handle both.
What to do: Before your first crop, measure the light at canopy height in the centre and in each corner. Use a light meter that counts the light plants can use (a PAR meter). This shows you whether plants at the edge get as much light as plants in the middle.
2. The air: read the VPD, not humidity alone
Judge the air by vapour pressure deficit (VPD), not by humidity alone. VPD is the gap between the moisture inside the leaf and the moisture in the air around it. A large gap pulls water out of the leaf quickly. A small gap slows it down.
The plant responds to this gap. It does not respond to the air temperature or the humidity reading on its own. That is why the same humidity reading can be fine at one temperature and wrong at another.
What to do: Hang a thermometer-hygrometer at canopy height, not on the wall by the door. Each day for 2 weeks, record temperature and humidity at three times: at lights-on, in the middle of the light period, and just after lights-off. Then work out the VPD for each reading using the climate topic linked above. This shows you when your room drifts furthest from its target.
3. The roots: what they grow in, and how often they are fed
The third choice is the material the roots grow in and how often you feed it. Here growers split into two groups:
- Recirculating systems. The nutrient solution drains back into the tank and is pumped to the plants again.
- Drain-to-waste systems. Each feed passes through the growing medium once and then drains away. Nothing is reused.
The choice matters because a recirculating system reuses the same solution. A problem in the tank reaches every plant connected to it. A drain-to-waste system uses more water and fertiliser, but every feed starts with fresh solution. Three common hydroponic setups are DWC (deep water culture), NFT (nutrient film technique) and drip:
- In DWC, the roots hang in an aerated solution.
- In NFT, a thin stream of solution runs along a channel past the roots.
- In drip, small emitters feed solution into each pot.
Translator’s note: In Thai heat, the tank in a recirculating system warms up along with the room. Warm solution is a known problem for roots (see the reservoir temperature topic). Power cuts also matter, especially during storms in the rainy season. When the pump or air pump stops, roots that depend on moving or aerated solution get no fresh supply until the power returns.
What to do: Before choosing a system, write down how often your area loses power and how long the cuts usually last. For each system you are considering, find out how long the roots can survive without the pump. If you are unsure, run a few plants through one full cycle before you convert the whole room. That trial shows you the risks at small cost.
Two lessons to learn early in a tropical climate
Removing moisture is often harder than cooling
In a tropical indoor room, removing moisture from the air (dehumidification) is often harder than cooling. It can also cost more than you expect.
Translator’s note: Here is why. Almost all the water the plants take up leaves through the leaves as vapour and ends up in the room air. In the rainy season, any outside air that leaks in is humid as well. An air conditioner removes water only while its compressor runs to cool the room. Once the room reaches the set temperature, the compressor slows or stops, and humidity climbs again. This is worst after lights-off, when the lamps stop producing heat. Sizing a dehumidifier for a Thai flowering room is covered in its own topic.
What to do: Use your 2-week log to find the highest humidity reading and when it happens. Then budget for the dehumidifier and the electricity it will use before you spend money on extra lamps. Otherwise you may add light to a room that is already too damp to use it.
Add CO₂ last
Adding CO₂ only pays off once light, temperature and feeding are already set as high as the plants can use. Until then, one of those three limits growth, and the extra CO₂ brings little gain. That is why CO₂ enrichment belongs at the end of your improvement list, not the start.
Translator’s note: Many Thai growers vent air outside to control heat and humidity. Any CO₂ you add leaves with the vented air.
What to do: Leave CO₂ off your shopping list for now. Consider it only when your light measurements and your climate log both show the room holding its targets.
Where to start: suggested reading order
Each topic below is linked where it first appears above.
- Indoor Grow Lights: LED vs HPS vs CMH: choose your lamp type.
- Light Spectrum and DLI: The Science of Cannabis Lighting: work out how much light your canopy needs each day.
- Grow Room Climate Control: VPD, Temperature, Humidity: set targets for your air and check them against your log.
- Hydroponic Cannabis: DWC, NFT and Drip Systems: choose a root system that suits your power supply and your heat.
- CO₂ Enrichment: When It Is Needed, When It Is Wasted: read this last, once the first four are under control.
Have a question about your own room? Post it in this board. Include the room size, the lamp, the air-conditioner size and a few days of temperature and humidity readings. With those details, other members can give you an answer that fits your setup.