Hempcrete in Thailand: How Well It Insulates, How Much Carbon It Stores, and Why It Cannot Carry a Building

Hempcrete is a wall material made from the woody core of the hemp stalk mixed with lime. It insulates reasonably well when the wall is thick, it is very good at evening out indoor humidity, and published life-cycle studies find it stores more carbon than it releases over a building’s life. Its compressive strength, however, is only 0.2 to 1.2 megapascals, roughly 10 to 100 times weaker than ordinary structural concrete. It cannot hold a building up. Any description that leaves this out is incomplete.


This article is about industrial hemp stalk, specifically its woody core (called shiv or hurd). It is not about cannabis flower. In Thailand, cannabis flower is a controlled herb and can be sold only on a PT 33 prescription. Nothing here is engineering advice. A qualified engineer must specify any building material against local building codes.

Why this matters to a hemp grower

When hemp is grown for fibre, the long outer fibre (bast fibre) is stripped from the stalk. What is left is the woody core, the shiv. Hempcrete is one of the few uses that can turn this leftover into a product with value. If you grow or plan to grow fibre hemp, hempcrete is one possible market for a by-product you will have anyway.

The material also matters for anyone who builds drying sheds, storage rooms or homes in a humid climate, because its strongest property is humidity control.

What to do with this section: if you grow fibre hemp, note how many tonnes of stalk you produce per season. That number is the starting point for any talk with a builder.

1. What hempcrete is

Hempcrete is made from three things: hemp shiv, a lime-based binder and water. The mix is cast into formwork or sprayed around a frame made of timber or steel. Once it sets, it forms a solid, insulating wall fill.

The name causes real confusion. Hempcrete is not concrete, and it cannot replace concrete. A better description is an insulating infill that is cast on site around a frame that carries the load.

Books and websites about cannabis often mention “Isochanvre”, a French hemp-lime product. They also often claim that hemp-lime buildings last for centuries. Hemp-lime building in France is real, and the modern revival of the technique did start there. But the “centuries” claim comes from very old buildings made with lime alone. Modern hempcrete has existed for only a few decades. So the claim is an argument by comparison with old lime buildings, not a measured lifespan for hempcrete.

What to do: when a seller or article quotes a lifespan in centuries, ask whether the figure was measured on hempcrete itself or borrowed from old lime buildings.

2. Two terms you need to read the numbers

Thermal conductivity (unit: W/m·K) describes the material itself. It tells you how much heat passes through a block of the material that is one metre thick, for each degree of temperature difference between its two sides. A lower number means the material lets less heat through, so it insulates better.

U-value (unit: W/m²·K) describes a whole wall at its actual thickness. It tells you how much heat passes through one square metre of that wall for each degree of difference between inside and outside. Again, lower is better. A thick wall made of a weak insulator can have the same U-value as a thin wall made of a strong insulator. To compare two walls, compare their U-values, not the conductivity of the materials.

Moisture buffering describes how a wall soaks up water vapour from the room when the air is humid and releases it again when the air dries. A wall that buffers well smooths out the daily swings in indoor humidity. The moisture buffer value is measured in grams of water per square metre of wall, for each one-percent change in relative humidity (RH).

What to do: before you compare any wall materials, write down which number you are looking at, conductivity of the material or U-value of the wall. Mixing them up is the most common mistake.

3. The measured properties

These values come from published research on building materials:

Property Measured range
Thermal conductivity Typically about 0.065–0.12 W/m·K. Collet & Pretot (2014, Construction and Building Materials) measured 0.09–0.16 W/m·K at 23 °C and 50% RH. When density rose by two-thirds, conductivity rose by about 54%.
Density Wall mixes typically weigh about 275–500 kg/m³. Lighter mixes are used for roof insulation and denser mixes for floors. Both conductivity and strength rise as density rises.
Compressive strength 0.2–1.2 MPa, rising with density.
Structural role Not load-bearing. It is used as a low-density insulating infill around a frame.
Moisture buffering Moisture buffer value about 2.0–2.15 g/(m²·%RH). Collet & Pretot (2012, Construction and Building Materials) measured 2.15 for sprayed hemp concrete. Collet et al. (2013, Energy and Buildings) rated three hemp concretes as “excellent or nearly excellent” at regulating humidity.
Carbon Net storage of 14–35 kg CO₂-eq per square metre of wall over 100 years (Pretot, Collet & Garnier, 2014, Building and Environment). The wall in that study used a lime-based binder, had a thermal resistance of 2.78 m²·K/W and was reported as about 26 cm thick.

“CO₂-eq” (carbon dioxide equivalent) is a way to add up different greenhouse gases as if they were all carbon dioxide. “MPa” (megapascal) measures how much pressure a material can take before it crushes. One megapascal is roughly the weight of 10 kg pressing on each square centimetre.

4. What each number means in practice

Insulation: it works only because the wall is thick

Common insulation boards and mats, such as mineral wool, expanded polystyrene (EPS) and polyisocyanurate (PIR) boards, have a conductivity of roughly 0.022–0.040 W/m·K. Hempcrete, at 0.065–0.12 W/m·K, lets about 2–3 times more heat through per centimetre. It is not in the same class as these materials.

Hempcrete walls still perform well because they are built thick, usually 250–400 mm. At about 300 mm, a hempcrete wall reaches a U-value of roughly 0.2 W/m²·K. The calculation is 0.30 m divided by 0.07 W/m·K, plus the small resistance of the air layers on each wall surface. That gives a U-value of about 0.22. UK suppliers quote about 0.2.

A modern wall with board insulation reaches a similar U-value with much less material. Hempcrete’s advantage is that it is one solid wall fill that lets water vapour pass through (“breathable”), instead of a mat or board plus plastic membranes. Its disadvantage is that thick walls take up floor area.

What to do: if you are costing a hempcrete building, calculate how much floor area a 300 mm wall takes compared with a thinner wall. On a small plot, that lost space can decide the question.

Strength: the reason it cannot carry a building

Structural concrete typically handles 20–40 MPa or more. Hempcrete handles 0.2–1.2 MPa, roughly 10 to 100 times less. It cannot carry the weight of a building.

Every hempcrete wall is therefore built around a timber or steel frame, and the frame carries all the load. The hemp-lime is cast around the frame to provide insulation and thermal mass (the ability to store heat and release it slowly).

This low strength is not a fault in the material. It is simply what the material is designed for: insulation. At the right thickness it does that job adequately. The problem is the name. “Hemp concrete” suggests a strength the material does not have. Anyone who plans a project based on the name will hit a wall at the engineering stage.

What to do: in any hempcrete plan you see, find the structural frame first. If a plan shows hempcrete walls carrying a roof or upper floor without a frame, stop and get an engineer’s opinion.

Humidity control: the most useful property in this region

A moisture buffer value of about 2 g/(m²·%RH) rates good to excellent on the scale of the Nordtest method, a standard laboratory test for moisture buffering. On that scale, “excellent” starts at 2.0.

In practice, the wall soaks up water vapour when indoor air is damp and releases it when the air dries. This reduces the swings in indoor humidity. In a tropical climate this is a major benefit, not a detail. It affects how likely mould is to grow, how comfortable the room feels and how hard the air conditioning has to work.

Translator’s note: Thai growers already fight humidity in drying rooms, storage rooms and homes, especially in the rainy season. A wall that buffers humidity does not replace a dehumidifier. It smooths the swings between day and night, which can make the dehumidifier’s job steadier. No published data on hempcrete drying rooms for cannabis were found for this article, so treat this as a reason to test, not as a proven result.

What to do: put a cheap digital hygrometer in the room you care about (drying room, store, bedroom) and log the humidity morning and evening for two weeks. The size of the daily swing tells you how much a humidity-buffering wall could help that room.

Carbon: real, but with a cost side

Hemp takes up CO₂ from the air as it grows. Lime also takes some CO₂ back as it hardens. This hardening process is called carbonation: the lime slowly turns back into limestone using CO₂ from the air.

Making lime, however, releases CO₂ in two ways. First, limestone gives off CO₂ when it is heated in a kiln to make lime (this step is called calcination). Second, the kiln burns fuel. Carbonation can at most win back part of the CO₂ from calcination. It never wins back the CO₂ from the fuel.

Carbonation is also slow. Arrigoni et al. (2017, Journal of Cleaner Production) found that after 240 days, only the outer layers of hempcrete blocks had carbonated to a significant degree.

Many commercial hemp binders are not pure lime. They are blends that include cement or pozzolans (materials such as volcanic ash that react with lime and help it set). These additions increase the carbon footprint of the binder. Pretot et al. (2014) found that producing the binder was the main source of the wall’s environmental impact.

The net figure of 14–35 kg CO₂-eq stored per square metre over 100 years is a whole-life figure, not something that happens on the day the wall is built. It depends on how thick the wall is, which binder is used, and how the hemp was farmed and transported.

For comparison, cement production accounts for around 8% of the world’s annual CO₂ emissions (Lehne & Preston, Chatham House, 2018). The comparison favours hempcrete, and it does not need to be exaggerated.

What to do: if you sell shiv or plan a building with a carbon target, ask the binder supplier exactly what the binder contains (pure lime, or lime with cement or pozzolans). That answer changes the carbon result more than anything else.

5. Where hempcrete fits, and where it does not

Good uses:

  • low-rise buildings with a timber or steel frame
  • walls where insulation and humidity control matter more than a thin wall
  • upgrading old buildings that have solid walls
  • climates with large swings in humidity
  • projects with a carbon target

Poor uses:

  • any wall that must carry load itself
  • below ground, or anywhere that stays wet
  • thin walls, because the insulation value comes only with thickness
  • places where there is no local supply of hemp shiv and lime

The last point is the one that matters most in Southeast Asia. The carbon advantage of hempcrete assumes the hemp is grown nearby. Shipping shiv across the world cancels that advantage. Shiv is also bulky and light, which makes freight expensive per kilogram. In short, hempcrete only makes sense when its raw materials are local.

What to do: before anything else, find out the distance from the nearest hemp field to the building site. If the shiv must be imported, hempcrete loses most of its point.

6. Hempcrete in a tropical climate

The tropics change the calculation in both directions.

In favour:

  • Humidity buffering is worth more here than in a cool climate.
  • The wall reduces heat gain, so the building needs less cooling. In this region, cooling is where most building energy goes.
  • Hemp grows fast in the right conditions.
  • Building with lime has a long history in the region.

Against:

  • Hempcrete must dry properly while it cures. In humid air, drying is slower.
  • Long periods of high humidity and wind-driven monsoon rain must be handled in the design, with roof overhangs, rain screens (an outer cladding layer that keeps rain off the wall) and renders that let water vapour pass.
  • Termites and other biological attack must be addressed. The lime binder is strongly alkaline (high pH), which is a real advantage here.
  • No publicly documented commercial supply chain for construction-grade shiv in the region was found when this article was prepared.

Translator’s note: with outside temperatures of 30–35 °C, a thick wall slows the heat entering the building during the day. Power cuts are a further point: a room that heats up more slowly stays usable longer when the air conditioning stops. Whether these effects are large enough to pay for the extra wall thickness in Thailand has not been measured in any study cited here.

Thailand already has a base for hemp fibre. The Highland Research and Development Institute (HRDI), which supports the highland work of the Royal Project, has developed fibre varieties low in tetrahydrocannabinol (THC). Hmong communities in the north have a long tradition of producing hemp fibre. Whether this base can supply construction-grade shiv in useful amounts has not been publicly documented.

So the realistic question in Thailand right now is not whether hempcrete performs. It is whether anyone can get the shiv. That is a question about hemp cultivation and processing before it is a question about building. Hemp textiles face the same bottleneck.

What to do: if you want to try hempcrete, start with one small test panel, for example a single wall section in a shed. Ask HRDI or a hemp fibre group in the north whether shiv is available, in what quantity and at what price. Then watch how long the panel takes to dry in the rainy season compared with the dry season.

7. The legal position in Thailand

Hemp stalk and shiv are industrial materials. They sit outside the controlled-herb rules that govern cannabis flower. In Thailand:

  • Flower is a controlled herb under the Notification of the Ministry of Public Health Re: Controlled Herbs (Cannabis), B.E. 2568, in force since 26 June 2025. It may be sold only with a PT 33 prescription.
  • Extracts above 0.2% THC by weight remain Category 5 narcotics under the Notification of the Ministry of Public Health Re: Specification of Category 5 Narcotics B.E. 2565 (2022), in force since 9 June 2022. A separate regulation, the Ministerial Regulation on Cannabis or Hemp Extracts B.E. 2569, in force since 26 April 2026, tightened licensing for these extracts. It does not create their Category 5 status.
  • Stalk, shiv and fibre have not been listed as narcotics since 9 June 2022. Only extracts remain on the Category 5 list. Check the current registration or permit requirements for growing and processing hemp with the Thai FDA and the Department of Agriculture.

The Cannabis Control Act is still a draft. The Cabinet approved the draft on 22 September 2026 and sent it to the House. If it becomes law, it may change how hemp is regulated.

Building materials must also meet Thai building codes and any relevant product standards.

What to do: before you invest in growing hemp for fibre and shiv, check the current permit position with the Department of Agriculture and the Thai FDA, and keep a copy of their answer with the date.

Share what you have found

Have you built with hemp-lime anywhere in the region, or tried to buy construction-grade shiv in Thailand or Vietnam? Please post below what you found and what price you were quoted. The material science is reasonably well established. The open question is the supply chain, and no public map of it has been found.

References

  • Collet, F. & Pretot, S. (2012). Experimental investigation of moisture buffering capacity of sprayed hemp concrete. Construction and Building Materials, 36, 58–65.
  • Collet, F. et al. (2013). Comparison of the hygric behaviour of three hemp concretes. Energy and Buildings.
  • Collet, F. & Pretot, S. (2014). Thermal conductivity of hemp concretes: Variation with formulation, density and water content. Construction and Building Materials.
  • Pretot, S., Collet, F. & Garnier, C. (2014). Life cycle assessment of a hemp concrete wall: Impact of thickness and coating. Building and Environment.
  • Arrigoni, A. et al. (2017). Life cycle assessment of natural building materials: the role of carbonation, mixture components and transport in the environmental impacts of hempcrete blocks. Journal of Cleaner Production, 149, 1051–1061.
  • Lehne, J. & Preston, F. (2018). Making Concrete Change: Innovation in Low-carbon Cement and Concrete. Chatham House.

General information, not engineering or legal advice. Specify building materials with a qualified engineer.